BeaverCraft · Paddle Strop · Sharpening & Knife Care
BeaverCraft LS6P1 Paddle Strop
Double-sided genuine leather on ash wood, with green M7 polishing compound
Your carving knife sliced cleanly yesterday, today it tears the wood fibres – usually the fine edge has simply rolled over or a burr is left behind. That does not mean a trip back to the whetstone: a few passes on the BeaverCraft LS6P1 Paddle Strop realign the edge. The rough suede side removes the burr, and the smooth side with the green M7 polishing compound refines the edge to a polished finish.
Buy the BeaverCraft LS6P1 Paddle Strop – keep your edges sharp without constant regrinding
The BeaverCraft LS6P1 Paddle Strop is a small, double-sided leather strop for honing carving knives, gouges and chisels, outdoor knives and kitchen knives after sharpening – and for bringing them back to full sharpness between sharpening sessions. The leather is fixed to a solid ash wood base that runs into an ergonomic handle. One side is covered with rough suede, the other with smooth leather, and both are 100 % genuine leather. The stropping surface measures 22 × 5 cm, and the whole strop is 35 cm long. A bar of green M7 polishing compound is included. If you want to buy a compact leather strop in Switzerland that earns its place in the carving workshop, the kitchen drawer and the outdoor kit alike, the BeaverCraft LS6P1 is a well-thought-out tool for knife care.
Suede · smooth leather · compound
Two leather sides and M7 compound – how a sharpened edge becomes a refined edge
Sharpening almost always leaves a fine burr on the edge, and even a keen blade loses its bite in use as the very edge rolls over slightly. This is where the BeaverCraft LS6P1 comes in. The rough suede side removes the burr and refines the sharpness. The smooth leather side then takes care of the final polish, up to a mirror-like finish. The supplied green M7 polishing compound has a grit of 7–5 µm and is based mainly on aluminium oxide; it is intended for hard metals such as stainless steel. You apply a thin layer to the leather and renew it once it has worn off.
Stropping instead of grinding – why your blade stays sharp for longer
Sharpening and stropping are two different steps. On a whetstone you remove steel and reshape the edge, which is necessary when a blade is dull or chipped. A strop removes hardly any material: it realigns the fine cutting edge, takes off the burr and polishes the bevel. Strop your blade regularly on the BeaverCraft LS6P1 and you will need the stone far less often, while the knife stays evenly sharp for longer. For the actual sharpening, you will find suitable stones and tools in our sharpener category – the strop then handles the final step.
From carving knife to chef’s knife – one strop for many blades
BeaverCraft designed the LS6P1 for different types of blades. In the carving workshop you strop your carving knives, which need a particularly fine edge for chip carving and spoon carving, as well as the outside of gouges and chisels. Outdoors it keeps your outdoor knife in shape, in the kitchen your chef’s knife. The LS6P1 is the smaller version of the BeaverCraft LS1P1. At 35 cm overall, it fits easily into a toolbox or drawer and can be held in one hand or laid flat on the table while you strop. Once honed, your carving tools can be stored neatly in the BeaverCraft TH10 tool holder, for example.
Stropping the right way – always spine first
When stropping, always pull the blade spine first across the leather, moving away from the edge – never push it edge first, or it will cut into the leather. Lay the blade flat at the angle of its bevel, draw it across the full length of the leather with light pressure, and switch sides after every stroke or every few strokes. Start on the suede side, then finish on the smooth side. To load the compound, simply rub the bar thinly over the leather. The hole in the ash wood handle lets you hang the strop on a hook after work, ready for the next session.
Genuine leather, ash wood, crafted in Ukraine
The BeaverCraft LS6P1 is made from a few solid materials: genuine leather on both sides, a base and handle of ash wood, and the BeaverCraft logo burnt into the side. The manufacturer makes its strops in Europe, in Ukraine to be precise. The strop is a natural companion to the brand’s carving knives and carving sets. You will find more tools and sets on our BeaverCraft brand page.
What the BeaverCraft LS6P1 Paddle Strop does – and what it does not
The strop is made for the final refinement: removing the burr, polishing the edge and maintaining sharpness between sharpening sessions. It does not replace a whetstone. If a blade is dull, chipped or has lost its edge angle, sharpen it first and then strop it on the leather. With the flat leather surface you reach the outside of gouges and hook knives; the inside curve requires a profiled strop. Knives and tools are not included. Once the supplied polishing compound is used up, you simply buy a new bar.
Key features – BeaverCraft LS6P1 Paddle Strop
- 🔄 Double-sided strop – suede side and smooth leather side
- 🟫 Suede side – removes the burr and refines sharpness
- ✨ Smooth leather side – final polish to a mirror-like finish
- 🐄 100 % genuine leather – on both sides
- 🟢 Green M7 polishing compound – 7–5 µm, aluminium oxide, included
- 🪵 Ash wood base and handle – ergonomic, with hanging hole
- 📏 35 cm overall length – leather surface 22 × 5 cm
- 🔪 For many blades – carving knives, gouges and chisels, outdoor and kitchen knives
- 🇺🇦 Made in Europe – crafted in Ukraine
- 🏅 2-year warranty – handled in Switzerland
Who is the BeaverCraft LS6P1 Paddle Strop for?
For woodcarvers who want to keep their knives and gouges sharp while they work, for bushcrafters and campers looking after their outdoor knife, for home cooks who appreciate sharp kitchen knives, and for DIY enthusiasts who keep their chisels in shape. Beginners in carving also benefit: the strop teaches early on how much difference a truly sharp edge makes. Buy the BeaverCraft LS6P1 Paddle Strop at Swiss-Sale.ch – your Swiss specialist shop for carving tools and knife care with fast shipping.
- Product type: Abrasive
Technical Specifications – BeaverCraft LS6P1 Paddle Strop
| Model | BeaverCraft LS6P1 |
|---|---|
| Brand | BeaverCraft |
| Product type | Paddle strop (double-sided leather strop) |
| Stropping surface | |
| Material | 100 % genuine leather, double-sided |
| Side 1 | Suede (rough) · burr removal, refining sharpness |
| Side 2 | Smooth leather · final honing, polishing |
| Leather surface (L × W) | 22 × 5 cm |
| Base and handle | |
| Material | Ash wood |
| Handle | ergonomic · with hanging hole |
| Overall length | 35 cm |
| Polishing compound | |
| Polishing compound | green · included |
| Grit | M7 (7–5 µm) |
| Abrasive | Aluminium oxide |
| Use | |
| Suitable for | Carving knives · gouges and chisels · outdoor knives · kitchen knives |
| Made in | Ukraine |
| Identification | |
| Manufacturer part no. | LS6P1 |
| EAN | 0655222645692 |
| Warranty | 2-year warranty |
Package Contents – BeaverCraft LS6P1 Paddle Strop
- 🪵 BeaverCraft LS6P1 paddle strop, double-sided (suede and smooth leather) on ash wood with handle
- 🟢 Green polishing compound M7 (7–5 µm) (1×)
Not included: knives and carving tools, a whetstone or sharpener for pre-sharpening dull blades, and replacement polishing compound (to be bought separately once the supplied bar is used up).
Frequently Asked Questions – BeaverCraft LS6P1 Paddle Strop
Here you will find answers about the BeaverCraft LS6P1 Paddle Strop – from its two leather sides and the M7 polishing compound to the right stropping technique, care, warranty and shipping within Switzerland.