BeaverCraft · Tool Holder · Carving Workshop
BeaverCraft TH10 Tool Holder
10 plywood slots for carving knives, hook knives and small gouges
Carving knives tossed into a drawer or box knock against each other, fine tips get damaged – and reaching in for the right one is an easy way to nick a finger. The BeaverCraft TH10 Tool Holder gives ten tools a fixed home: the handles sit in 35 mm holes and the blades rest below on foam pads, whether the holder stands on your table or workbench or hangs on the wall.
Buy the BeaverCraft TH10 Tool Holder – every carving tool in its place
The BeaverCraft TH10 Tool Holder is a plywood storage stand for up to ten woodcarving tools: whittling knives, spoon carving knives (hook knives), small gouges and chisels – from BeaverCraft or any other maker. At the top, a rack with ten 35 mm holes guides the handles; below it, each blade stands in its own slot with a foam pad on the bottom. The edges never touch each other, the tips never hit bare wood, and you can pick up any tool with one movement of your hand. Set the TH10 on a table or workbench, or hang it on the wall using the two keyhole slots in the back panel. It measures 250 × 220 × 105 mm, weighs 400 g and comes as a kit that slots together without glue or screws. If you want to buy a carving tool holder in Switzerland that keeps your bench tidy and your blades protected, the BeaverCraft TH10 is built for exactly that.
Hole rack · slot · foam pad
Handle guided at the top, blade cushioned below – why the edges stay intact
A carving knife does not only lose its edge while you work – it can also suffer in storage. When several blades share a drawer, they clatter against each other, and fine tips or the edge of a hook knife pick up nicks. The BeaverCraft TH10 separates your tools twice over. The hole rack, at a height of 95 mm, keeps each handle upright in its own 35 mm hole, while the blade below stands in a separate slot. A polymer foam pad lines the bottom of every slot, so the tip lands on something soft instead of wood. The ten holes and slots are arranged in two staggered rows of five, which keeps the stand compact and lets you see every handle at a glance.
A tidy carving bench – find tools without searching, grab them with one hand
Carving means switching tools constantly: a straight knife to rough out the blank, a hook knife to hollow the bowl of a spoon, a gouge for the details. When everything lies in a heap, every search interrupts your flow – and putting things away between steps tends to get skipped. In the BeaverCraft TH10 Tool Holder each tool has a fixed spot. You soon know where every knife stands and can lift it out with one hand without looking. That saves time, keeps your work surface clear and makes carving safer, because no open blade is lying next to the workpiece. Blades to fill the ten slots are waiting in our carving knives category.
Table, workbench or wall – two ways to set up the TH10
Freestanding, the BeaverCraft TH10 Tool Holder sits on a table or workbench and, at 105 mm deep, takes up little space. At 400 g it is easy to bring to your workplace along with the tools – from the shelf to the kitchen table, for example. If you would rather keep the surface completely clear, hang it on the wall: two keyhole slots are cut into the back panel and slip over two screw heads. Screws and wall plugs are not included – choose them to suit your wall (wood, concrete, plasterboard) so that the holder and its tools hang securely.
A kit without glue or screws – slotted together and locked with wooden pins
The TH10 arrives as a flat-pack kit. The plywood parts engage with tabs in matching slots and are secured with small wooden locking pins – no glue or screws needed, and everything required is in the box, including the ten foam pads for the slots. The manufacturer’s assembly photos show how the side panels, back panel, dividers and hole rack fit together. The BeaverCraft logo is engraved on the back panel. If you are just getting started, a set of matched knives is a good way in – take a look at our carving sets.
Stored neatly, kept sharp – the TH10 and the LS6P1 paddle strop
A tool holder protects your edges from damage in storage, but it cannot keep them sharp. That is where the small, double-sided BeaverCraft LS6P1 paddle strop with green polishing compound comes in: a few passes before you put a knife back, and it is ready to go next time. Together, the two cover the daily routine at the carving bench – store tools within reach and keep them keen. More knives, sets and accessories from the brand are on our BeaverCraft brand page.
What the BeaverCraft TH10 Tool Holder does – and what it doesn’t
The TH10 is an open stand for your workplace: it sorts up to ten carving tools, protects their tips and keeps them within reach. It is not a closed box with a lid and not a travel case – on the road, a tool roll or the knives’ own sheaths are the better choice. Whether a tool fits depends on its handle: it has to pass through a 35 mm hole, so very thick handles or large chisels with wide blades are not what it is designed for. Not included are the carving tools themselves and the screws and wall plugs for wall mounting. Being natural plywood, the holder belongs in a dry spot.
Key features – BeaverCraft TH10 Tool Holder
- 🗂️ 10 slots – for carving knives, hook knives, small gouges and chisels
- ⭕ 10 holes of 35 mm – hole rack at 95 mm height guides the handles
- 🧽 Foam pads – on the bottom of every slot, protect the blade tips
- 🪵 Natural plywood – BeaverCraft logo on the back panel
- 🧩 Slot-together kit – no glue or screws, locking pins included
- 🖼️ Wall mounting – 2 keyhole slots in the back panel
- 🛠️ Freestanding – on a table or workbench
- 📏 250 × 220 × 105 mm – width × height × depth
- ⚖️ 400 g
- 🏅 2-year warranty – handled in Switzerland
Who is the BeaverCraft TH10 Tool Holder for?
For woodcarvers whose knife collection has outgrown its tool roll, for spoon carvers with several hook and whittling knives, for anyone setting up a permanent carving corner in a hobby workshop or at the kitchen table, for course leaders who want to lay out tools clearly, and as a gift for carvers who already own a few tools. Buy the BeaverCraft TH10 Tool Holder at Swiss-Sale.ch – your Swiss specialist shop for carving tools with fast shipping.
Technical Specifications – BeaverCraft TH10 Tool Holder
| Model | BeaverCraft TH10 |
|---|---|
| Brand | BeaverCraft |
| Product type | Tool holder |
| Construction | |
| Material | Plywood, natural |
| Slots | 10 (2 rows of 5) |
| Hole diameter | 35 mm |
| Padding | Polymer foam on the bottom of every slot (10×) |
| Assembly | Slot-together kit with locking pins · no glue or screws |
| Placement | Table or workbench · wall mounting via 2 keyhole slots |
| Suitable for | Carving knives · spoon carving knives (hook knives) · small gouges · chisels |
| Dimensions and weight | |
| Width | 250 mm |
| Height | 220 mm |
| Depth | 105 mm |
| Rack height | 95 mm |
| Weight | 400 g |
| Identification | |
| Manufacturer part no. | TH10 |
| EAN | 0655222645821 |
| Warranty | 2-year warranty |
Package Contents – BeaverCraft TH10 Tool Holder
- 🧰 BeaverCraft TH10 tool holder as a kit (plywood parts, natural)
- 📌 Locking pins made of wood for the slot joints
- 🧽 Foam pads for the slots (10×)
Not included: carving tools (knives, gouges and chisels) and screws and wall plugs for wall mounting. No glue is needed for assembly.
Frequently Asked Questions – BeaverCraft TH10 Tool Holder
Here you will find answers about the BeaverCraft TH10 Tool Holder – from slots, hole size and dimensions to assembly and wall mounting, safe storage of your blades and shipping within Switzerland.